⛄ 2010 Honda Accord 2.4 Cylinder Head Torque Specs

Hereis the torque again. Tighten the cylinder head bolts sequentially in 3 steps. 1st step torque: 20 Nm (2.0 kgf-cm, 14 ft. Lbs.) 2nd step torque: 49 Nm (5.0 kgf-cm, 36 ft. Lbs.) 3rd step torque: 67 Nm (6.8 kgf-cm, 49 ft. Lbs.) Larger view (below) of every step to do a head gasket on this car. SKU# 1043164. Check if this fits your 2010 Honda Accord. Notes: With California emission system. OEM fine wire double iridium. Original center electrode material is iridium and ground electrode pin material is platinum. Do not gap, gap is preset. Quantity per car: 4. PRICE: 13.99. Hex Size: 16 mm. Howfast is a 2010 Honda Accord 8 2.2 i-DTEC Executive? The {carro} can reach 0 to 100 km/h (0 to 62 mph) in 9.8 seconds and has a top speed of 132 mph. Related car specs TimingBelt cover - 7.2 ftlbs. Lower Alternator bolt - 33 ftlbs. Upper Alternator bolt - 17 ftlbs. Power Steering pump bolts - 17 ftlbs. Side engine mounts 38 ftlbs. AC idler pulley 33 ft lbs. Timing belt tensioner bolt 40 ftlbs. CKF sensor mounting bolts - 8 ftlbs. Distributer hold down bolts - 17 ftlbs. TheHonda Accord oil drain plug torque is 25 foot-pounds. Your oil needs to be replaced eventually. Every 5,000 to 10,000 miles is a good rule of thumb. If You don't replace it, there will be issues with the engine. Having high quality oil is key for the engine to run smoothly. You will run into problems with the oil at some point. Bad oil can cause the 2007Accord 2.4 LX 4dr Sedan specs (horsepower, torque, engine size, wheelbase), MPG and pricing. 2007 Honda Accord Specs Specs Equipment Interior: Front head room: 40 "Rear head room: 39 Thetables after it contain all torque spec values I could find. Most-used torque settings for Honda Odyssey US 3. Part Description Torque (Nm) Torque (ft/lbs) Remarks Applies to; Oil pan: Drain plug: 49: 36: Cylinder head: Cylinder head bolts: 39: 29: 6-points bolts, Step 1: Cylinder head: Cylinder head bolts: 69: 51: 2003honda odyssey 3.5 head bolt torque spec. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Feb 28, 2014 • 2000 Honda Odyssey. Mainbearings: Torque the main bearing cap bolts in three stages in the following sequence:Stage 1: 30 Nm (22 lb-ft) Stage 2: 80 Nm (59 lb-ft) Stage 3: 90 degrees. After the final torque of 90 degrees, check the bolt stretch with a torque angle gauge. The stretch should be between 0.15mm and 0.30mm. Seeanswer (1) Best Answer. Copy. Honda Accord 1977-1993 1.8Ltr Engine code F18A2 2.0Ltr Engine codes F20A2 F20A2/3/6 F20A4 F20A5F20A8 2.2Ltr Engine code F22A3 All torque figures are listed as 1/ 3. 5. Remove the Side Engine Mount. Support the engine from canting with a hydraulic jack when the side engine mount is removed. To prevent damage to the oil pan, place a flat piece of wood between the oil pan and the hydraulic jack. Remove the ground strap followed by the two nuts and one bolt. Getaccurate and up-to-date timing belt data for your Honda Accord by year and model. TimingBeltInfo.com. About. Home; Honda Accord Honda Accord Timing Belt Or Timing Chain (1990 - 2023) 2010: K24Z2/K24Z3 2.4L 4 Cyl. 177 hp / 190 hp: timing chain: interference: lifetime: 2010: J35Z2/J35Z3 3.5L V6 268 hp / 270 hp: timing belt: .

2010 honda accord 2.4 cylinder head torque specs